You can configure Windows Server 2012 R2 as a customer gateway device for your VPC. Use the following process whether you are running Windows Server 2012 R2 on an EC2 instance in a VPC, or on your own server.

Topics

Configuring your Windows server

To configure your Windows server as a customer gateway device, ensure that you have Windows Server 2012 R2 on your own network, or on an EC2 instance in a VPC. If you use an EC2 instance that you launched from a Windows AMI, do the following:

  • Disable source/destination checking for the instance:Open the Amazon EC2 console at https://console.aws.amazon.com/ec2/
  • Select your Windows Server instance, and choose Actions, Networking, Change Source/Dest. Check. Choose Yes, Disable.
  • Update your adapter settings so that you can route traffic from other instances:
    1. Connect to your Windows instance. For more information, see Connecting to your Windows instance.
    2. Open the Control Panel, and start the Device Manager.
    3. Expand the Network adapters node.
    4. Select the AWS PV network device, choose Action, Properties.
    5. On the Advanced tab, disable the IPv4 Checksum Offload, TCP Checksum Offload (IPv4), and UDP Checksum Offload (IPv4) properties, and then choose OK.
  • Allocate an Elastic IP address to your account and associate it with the instance. For more information, see Working with Elastic IP addresses. Take note of this address — you need it when you create the customer gateway in your VPC.
  • Ensure that the instance’s security group rules allow outbound IPsec traffic. By default, a security group allows all outbound traffic. However, if the security group’s outbound rules have been modified from their original state, you must create the following outbound custom protocol rules for IPsec traffic: IP protocol 50, IP protocol 51, and UDP 500.

Take note of the CIDR range for your network in which the Windows server is located, for example, 172.31.0.0/16.

Step 1: Create a VPN connection and configure your VPC

To create a VPN connection from your VPC, you must first create a virtual private gateway and attach it to your VPC. For more information, see Create a virtual private gateway.

Then, create a VPN connection and new customer gateway. For the customer gateway, specify the public IP address of your Windows server. For the VPN connection, choose static routing, and then enter the CIDR range for your network in which the Windows server is located, for example, 172.31.0.0/16. For more information, see Create a Site-to-Site VPN connection.

To configure your VPC

  • Create a private subnet in your VPC (if you don’t have one already) for launching instances to communicate with the Windows server. For more information, see Adding a subnet to your VPC.
  • Note A private subnet is a subnet that does not have a route to an internet gateway. The routing for this subnet is described in the next item.
  • Update your route tables for the VPN connection:
    • Add a route to your private subnet’s route table with the virtual private gateway as the target, and the Windows server’s network (CIDR range) as the destination.
    • Enable route propagation for the virtual private gateway. For more information, see Route tables in the Amazon VPC User Guide.
  • Create a security group configuration for your instances that allows communication between your VPC and network:
    • Add rules that allow inbound RDP or SSH access from your network. This enables you to connect to instances in your VPC from your network. For example, to allow computers in your network to access Linux instances in your VPC, create an inbound rule with a type of SSH, and the source set to the CIDR range of your network (for example, 172.31.0.0/16). For more information, see Security groups for your VPC in the Amazon VPC User Guide.
    • Add a rule that allows inbound ICMP access from your network. This enables you to test your VPN connection by pinging an instance in your VPC from your Windows server.

Step 2: Download the configuration file for the VPN connection

You can use the Amazon VPC console to download a Windows server configuration file for your VPN connection.

To download the configuration file

  1. Open the Amazon VPC console at https://console.aws.amazon.com/vpc/
  2. In the navigation pane, choose Site-to-Site VPN Connections.
  3. Select your VPN connection and choose Download Configuration.
  4. Select Microsoft as the vendor, Windows Server as the platform, and 2012 R2 as the software. Choose Download. You can open the file or save it.

The configuration file contains a section of information similar to the following example. You see this information presented twice, one time for each tunnel. Use this information when configuring the Windows Server 2012 R2 server.





vgw-1a2b3c4d Tunnel1
--------------------------------------------------------------------	
Local Tunnel Endpoint:       203.0.113.1
Remote Tunnel Endpoint:      203.83.222.237
Endpoint 1:                  [Your_Static_Route_IP_Prefix]
Endpoint 2:                  [Your_VPC_CIDR_Block]
Preshared key:               xCjNLsLoCmKsakwcdoR9yX6GsEXAMPLE

Local Tunnel Endpoint

The IP address for the customer gateway—in this case, your Windows server—that terminates the VPN connection on your network’s side. If your customer gateway is a Windows server instance, this is the instance’s private IP address. Remote Tunnel Endpoint

One of two IP addresses for the virtual private gateway that terminates the VPN connection on the AWS side of the connection. Endpoint 1

The IP prefix that you specified as a static route when you created the VPN connection. These are the IP addresses in your network that are allowed to use the VPN connection to access your VPC. Endpoint 2

The IP address range (CIDR block) of the VPC that is attached to the virtual private gateway (for example 10.0.0.0/16). Preshared key

The pre-shared key that is used to establish the IPsec VPN connection between Local Tunnel Endpoint and Remote Tunnel Endpoint.

We suggest that you configure both tunnels as part of the VPN connection. Each tunnel connects to a separate VPN concentrator on the Amazon side of the VPN connection. Although only one tunnel at a time is up, the second tunnel automatically establishes itself if the first tunnel goes down. Having redundant tunnels ensure continuous availability in the case of a device failure. Because only one tunnel is available at a time, the Amazon VPC console indicates that one tunnel is down. This is expected behavior, so there’s no action required from you.

With two tunnels configured, if a device failure occurs within AWS, your VPN connection automatically fails over to the second tunnel of the AWS virtual private gateway within a matter of minutes. When you configure your customer gateway device, it’s important that you configure both tunnels. Note

From time to time, AWS performs routine maintenance on the virtual private gateway. This maintenance might disable one of the two tunnels of your VPN connection for a brief period of time. Your VPN connection automatically fails over to the second tunnel while we perform this maintenance.

Additional information regarding the Internet Key Exchange (IKE) and IPsec Security Associations (SA) is presented in the downloaded configuration file. Because the VPC VPN suggested settings are the same as the Windows Server 2012 R2 default IPsec configuration settings, minimal work is needed on your part.





MainModeSecMethods:        DHGroup2-AES128-SHA1
MainModeKeyLifetime:       480min,0sess
QuickModeSecMethods:       ESP:SHA1-AES128+60min+100000kb
QuickModePFS:              DHGroup2

MainModeSecMethods

The encryption and authentication algorithms for the IKE SA. These are the suggested settings for the VPN connection, and are the default settings for Windows Server 2012 R2 IPsec VPN connections. MainModeKeyLifetime

The IKE SA key lifetime.  This is the suggested setting for the VPN connection, and is the default setting for Windows Server 2012 R2 IPsec VPN connections. QuickModeSecMethods

The encryption and authentication algorithms for the IPsec SA. These are the suggested settings for the VPN connection, and are the default settings for Windows Server 2012 R2 IPsec VPN connections. QuickModePFS

We suggest that you use master key perfect forward secrecy (PFS) for your IPsec sessions.

Step 3: Configure the Windows server

Before you set up the VPN tunnel, you must install and configure Routing and Remote Access Services on your Windows server. That allows remote users to access resources on your network.

To install Routing and Remote Access Services on Windows Server 2012 R2

  1. Log on to the Windows Server 2012 R2 server.
  2. Go to the Start menu, and choose Server Manager.
  3. Install Routing and Remote Access Services:
    1. From the Manage menu, choose Add Roles and Features.
    2. On the Before You Begin page, verify that your server meets the prerequisites, and then choose Next.
    3. Choose Role-based or feature-based installation, and then choose Next.
    4. Choose Select a server from the server pool, select your Windows 2012 R2 server, and then choose Next.
    5. Select Network Policy and Access Services in the list. In the dialog box that displays, choose Add Features to confirm the features that are required for this role.
    6. In the same list, choose Remote Access, Next.
    7. On the Select features page, choose Next.
    8. On the Network Policy and Access Services page, choose Next. Leave Network Policy Server selected, and then choose Next.
    9. On the Remote Access page, choose Next. On the next page, select DirectAccess and VPN (RAS). In the dialog box that displays, choose Add Features to confirm the features that are required for this role service. In the same list, select Routing, and then choose Next.
    10. On the Web Server Role (IIS) page, choose Next. Leave the default selection, and choose Next.
    11. Choose Install. When the installation completes, choose Close.

To configure and enable Routing and Remote Access Server

  1. On the dashboard, choose Notifications (the flag icon). There should be a task to complete the post-deployment configuration. Choose the Open the Getting Started Wizard link.
  2. Choose Deploy VPN only.
  3. In the Routing and Remote Access dialog box, choose the server name, choose Action, and then select Configure and Enable Routing and Remote Access.
  4. In the Routing and Remote Access Server Setup Wizard, on the first page, choose Next.
  5. On the Configuration page, choose Custom Configuration, Next.
  6. Choose LAN routing, Next, Finish.
  7. When prompted by the Routing and Remote Access dialog box, choose Start service.

Step 4: Set up the VPN tunnel

You can configure the VPN tunnel by running the netsh scripts included in the downloaded configuration file, or by using the New Connection Security Rule wizard on the Windows server. Important

We suggest that you use master key perfect forward secrecy (PFS) for your IPsec sessions. If you choose to run the netsh script, it includes a parameter to enable PFS (qmpfs=dhgroup2). You cannot enable PFS using the Windows Server 2012 R2 user interface — you must enable it using the command line.

Option 1: Run netsh script

Copy the netsh script from the downloaded configuration file and replace the variables. The following is an example script.





netsh advfirewall consec add rule Name="vgw-1a2b3c4d Tunnel 1" ^
Enable=Yes Profile=any Type=Static Mode=Tunnel ^
LocalTunnelEndpoint=Windows_Server_Private_IP_address ^
RemoteTunnelEndpoint=203.83.222.236 Endpoint1=Your_Static_Route_IP_Prefix ^
Endpoint2=Your_VPC_CIDR_Block Protocol=Any Action=RequireInClearOut ^
Auth1=ComputerPSK Auth1PSK=xCjNLsLoCmKsakwcdoR9yX6GsEXAMPLE ^
QMSecMethods=ESP:SHA1-AES128+60min+100000kb ^
ExemptIPsecProtectedConnections=No ApplyAuthz=No QMPFS=dhgroup2

Name: You can replace the suggested name (vgw-1a2b3c4d Tunnel 1) with a name of your choice.

LocalTunnelEndpoint: Enter the private IP address of the Windows server on your network.

Endpoint1: The CIDR block of your network on which the Windows server resides, for example, 172.31.0.0/16.

Endpoint2: The CIDR block of your VPC or a subnet in your VPC, for example, 10.0.0.0/16.

Run the updated script in a command prompt window on your Windows server. (The ^ enables you to cut and paste wrapped text at the command line.) To set up the second VPN tunnel for this VPN connection, repeat the process using the second netsh script in the configuration file.

When you are done, go to 2.4: Configure the Windows firewall.

For more information about the netsh parameters, see Netsh AdvFirewall Consec Commands

in the Microsoft TechNet Library.

Option 2: Use the Windows server user interface

You can also use the Windows server user interface to set up the VPN tunnel. This section guides you through the steps. Important

You can’t enable master key perfect forward secrecy (PFS) using the Windows Server 2012 R2 user interface. You must enable PFS using the command line, as described in Enable master key perfect forward secrecy.

Topics

2.1: Configure a security rule for a VPN tunnel

In this section, you configure a security rule on your Windows server to create a VPN tunnel.

To configure a security rule for a VPN tunnel

  1. Open Server Manager, choose Tools, and then select Windows Firewall with Advanced Security.
  2. Select Connection Security Rules, choose Action, and then New Rule.
  3. In the New Connection Security Rule wizard, on the Rule Type page, choose Tunnel, and then choose Next.
  4. On the Tunnel Type page, under What type of tunnel would you like to create, choose Custom configuration. Under Would you like to exempt IPsec-protected connections from this tunnel, leave the default value checked (No. Send all network traffic that matches this connection security rule through the tunnel), and then choose Next.
  5. On the Requirements page, choose Require authentication for inbound connections. Do not establish tunnels for outbound connections, and then choose Next.
  6. On the Tunnel Endpoints page, under Which computers are in Endpoint 1, choose Add. Enter the CIDR range of your network (behind your Windows server customer gateway device; for example, 172.31.0.0/16), and then choose OK. The range can include the IP address of your customer gateway device.
  7. Under What is the local tunnel endpoint (closest to computer in Endpoint 1), choose Edit. In the IPv4 address field, enter the private IP address of your Windows server, and then choose OK.
  8. Under What is the remote tunnel endpoint (closest to computers in Endpoint 2), choose Edit. In the IPv4 address field, enter the IP address of the virtual private gateway for Tunnel 1 from the configuration file (see Remote Tunnel Endpoint), and then choose OK.

Important

If you are repeating this procedure for Tunnel 2, be sure to select the endpoint for Tunnel 2.

Under Which computers are in Endpoint 2, choose Add. In the This IP address or subnet field, enter the CIDR block of your VPC, and then choose OK. Important

You must scroll in the dialog box until you locate Which computers are in Endpoint 2. Do not choose Next until you have completed this step, or you won’t be able to connect to your server.


									New Connection Security Rule Wizard: Tunnel
										Endpoints

Confirm that all of the settings you’ve specified are correct and then choose Next.

On the Authentication Method page, select Advanced and choose Customize.

Under First authentication methods, choose Add.

Select Preshared key, enter the pre-shared key value from the configuration file and then choose OK.

  1. Important If you are repeating this procedure for Tunnel 2, be sure to select the pre-shared key for Tunnel 2.
  2. Ensure that First authentication is optional is not selected, and choose OK.
  3. Choose Next.
  4. On the Profile page, select all three check boxes: Domain, Private, and Public. Choose Next.
  5. On the Name page, enter a name for your connection rule; for example, VPN to AWS Tunnel 1, and then choose Finish.

Repeat the preceding procedure, specifying the data for Tunnel 2 from your configuration file.

After you’ve finished, you’ll have two tunnels configured for your VPN connection.

2.3: Confirm the tunnel configuration

To confirm the tunnel configuration

  1. Open Server Manager, choose Tools, select Windows Firewall with Advanced Security, and then select Connection Security Rules.
  2. Verify the following for both tunnels:
    • Enabled is Yes
    • Endpoint 1 is the CIDR block for your network
    • Endpoint 2 is the CIDR block of your VPC
    • Authentication mode is Require inbound and clear outbound
    • Authentication method is Custom
    • Endpoint 1 port is Any
    • Endpoint 2 port is Any
    • Protocol is Any
  3. Select the first rule and choose Properties.
  4. On the Authentication tab, under Method, choose Customize. Verify that First authentication methods contains the correct pre-shared key from your configuration file for the tunnel, and then choose OK.
  5. On the Advanced tab, verify that Domain, Private, and Public are all selected.
  6. Under IPsec tunneling, choose Customize. Verify the following IPsec tunneling settings, and then choose OK and OK again to close the dialog box.
    • Use IPsec tunneling is selected.
    • Local tunnel endpoint (closest to Endpoint 1) contains the IP address of your Windows server. If your customer gateway device is an EC2 instance, this is the instance’s private IP address.
    • Remote tunnel endpoint (closest to Endpoint 2) contains the IP address of the virtual private gateway for this tunnel.
  7. Open the properties for your second tunnel. Repeat steps 4 to 7 for this tunnel.

Enable master key perfect forward secrecy

You can enable master key perfect forward secrecy by using the command line. You cannot enable this feature using the user interface.

To enable master key perfect forward secrecy

  1. In your Windows server, open a new command prompt window.
  2. Enter the following command, replacing rule_name with the name that you gave the first connection rule.
  1. netsh advfirewall consec set rule name="rule_name" new QMPFS=dhgroup2 QMSecMethods=ESP:SHA1-AES128+60min+100000kb
  2. Repeat step 2 for the second tunnel, this time replacing rule_name with the name that you gave the second connection rule.

2.4: Configure the Windows firewall

After setting up your security rules on your server, configure some basic IPsec settings to work with the virtual private gateway.

To configure the Windows firewall

  1. Open Server Manager, choose Tools, select Windows Firewall with Advanced Security, and then choose Properties.
  2. On the IPsec Settings tab, under IPsec exemptions, verify that Exempt ICMP from IPsec is No (default). Verify that IPsec tunnel authorization is None.
  3. Under IPsec defaults, choose Customize.
  4. Under Key exchange (Main Mode), select Advanced and then choose Customize.
  5. In Customize Advanced Key Exchange Settings, under Security methods, verify that the following default values are used for the first entry:
    • Integrity: SHA-1
    • Encryption: AES-CBC 128
    • Key exchange algorithm: Diffie-Hellman Group 2
    • Under Key lifetimes, verify that Minutes is 480 and Sessions is 0.
    These settings correspond to these entries in the configuration file.
MainModeSecMethods: DHGroup2-AES128-SHA1,DHGroup2-3DES-SHA1
MainModeKeyLifetime: 480min,0sec

Under Key exchange options, select Use Diffie-Hellman for enhanced security, and then choose OK.

Under Data protection (Quick Mode), select Advanced, and then choose Customize.

Select Require encryption for all connection security rules that use these settings.

Under Data integrity and encryption, leave the default values:

  • Protocol: ESP
  • Integrity: SHA-1
  • Encryption: AES-CBC 128
  • Lifetime: 60 minutes

These values correspond to the following entry from the configuration file.

  1. QuickModeSecMethods: ESP:SHA1-AES128+60min+100000kb
  2. Choose OK to return to the Customize IPsec Settings dialog box and choose OK again to save the configuration.

Step 5: Enable dead gateway detection

Next, configure TCP to detect when a gateway becomes unavailable. You can do this by modifying this registry key: HKLM\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters. Do not perform this step until you’ve completed the preceding sections. After you change the registry key, you must reboot the server.

To enable dead gateway detection

  1. From your Windows server, launch the command prompt or a PowerShell session, and enter regedit to start Registry Editor.
  2. Expand HKEY_LOCAL_MACHINE, expand SYSTEM, expand CurrentControlSet, expand Services, expand Tcpip, and then expand Parameters.
  3. From the Edit menu, select New and select DWORD (32-bit) Value.
  4. Enter the name EnableDeadGWDetect.
  5. Select EnableDeadGWDetect and choose Edit, Modify.
  6. In Value data, enter 1, and then choose OK.
  7. Close the Registry Editor and reboot the server.

For more information, see EnableDeadGWDetect

in the Microsoft TechNet Library.

Step 6: Test the VPN connection

To test that the VPN connection is working correctly, launch an instance into your VPC, and ensure that it does not have an internet connection. After you’ve launched the instance, ping its private IP address from your Windows server. The VPN tunnel comes up when traffic is generated from the customer gateway device. Therefore, the ping command also initiates the VPN connection.

For steps to test the VPN connection, see Testing the Site-to-Site VPN connection.

If the ping command fails, check the following information:

  • Ensure that you have configured your security group rules to allow ICMP to the instance in your VPC. If your Windows server is an EC2 instance, ensure that its security group’s outbound rules allow IPsec traffic. For more information, see Configuring your Windows server.
  • Ensure that the operating system on the instance you are pinging is configured to respond to ICMP. We recommend that you use one of the Amazon Linux AMIs.
  • If the instance you are pinging is a Windows instance, connect to the instance and enable inbound ICMPv4 on the Windows firewall.
  • Ensure that you have configured the route tables correctly for your VPC or your subnet. For more information, see Step 1: Create a VPN connection and configure your VPC.
  • If your customer gateway device is a Windows server instance, ensure that you’ve disabled source/destination checking for the instance. For more information, see Configuring your Windows server.

In the Amazon VPC console, on the VPN Connections page, select your VPN connection. The first tunnel is in the UP state. The second tunnel should be configured, but it isn’t used unless the first tunnel goes down. It may take a few moments to establish the encrypted tunnels.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

The reCAPTCHA verification period has expired. Please reload the page.